PRIS:17 000 kr med media kort

Rega Planar 6 Skivspelare

Denna skivspelare kan du köpa med pic-up MM Exact Rega då kostar spelaren 17000:- eller så kan du välja MC  Ania  då kostar spelaren 20000:-.

 

 

Planar 6 & Neo PSU
The Planar 6 has one goal, to reproduce your vinyl as accurately as possible. We have engineered every aspect of this turntable to extract as much detail from the vinyl surface as possible. Advanced materials and engineering solutions have been used throughout the design to ensure the greatest level of performance.The Neo PSU offers electronic speed change, advanced anti-vibration control and user adjustable electronic fine speed adjustment only found on the RP10 until now. See ‘product details’ tab below for full information.

The Planar 6 will be available with the recommended *Ania MC factory fitted as an attractive package.

*All images shown include the Ania MC, sold separately or factory fitted if required.
The Planar 6 is built around the huge success of the RP8 and RP10 turntables. It is the first new Rega turntable to be constructed with an ultra lightweight Tancast 8 polyurethane foam core plinth (a material developed for the aerospace industry). This material is sandwiched between a new HPL (high pressure laminate). HPL is exceptionally thin whilst extremely rigid and is presented in a stunning Polaris matt grey finished with high gloss polymer black edge trim.

The Planar 6 now benefits from a single piece, machined aluminum sub-platter, a new 24v motor hand tuned and matched to its own NEO power supply and custom drive pulley fitted with our upgrade drive belt as standard.

The Neo PSU uses the RP10 DSP (digital signal processing) generator built upon a high stability crystal. The DSP generator will divide the accurate signal from the crystal to the exact frequency required to turn the platter at the selected speed. The DSP generator will also produce a near perfect sinusoidal waveform to drive the motor. This, along with an efficient drive amplifier, generates a 24V AC balanced signal of less than 0.15% distortion, which is completely un-affected by any changes in the mains/line voltage and conditions. This then drives the turntables anti-vibration circuit, which is situated beneath the turntable.

Key Features:

NEO power supply.
Super lightweight foam core plinth.
Plinth laminate: New Polaris HPL (high pressure laminate). Non-marking matt finish scratch resistant high rigidity skin.
Available in one finish ‘Polaris Grey’ matt finish with high gloss black polymer edge trim.
Upgrade white drive belt fitted as standard.
Custom dual layer smoked / clear float glass platter.
Single piece aluminium sub platter.
Custom machined high precision drive pulley.
Patent pending, ultra-low friction central brass hub.
Rega’s double brace technology, with integral custom matched aluminium tonearm and hub pillars to ensure maximum rigidity and accuracy.
RB330 handmade precision tonearm with custom stainless weight.
New high spec Rega 24v low noise synchronous motor – each motor matched by hand to its own NEO PSU ensuring optimum anti-vibration control.
New smoked dust cover.
New aluminium foot trims and Planar style feet.
Available with Ania MC cartridge factory fitted / Discount available when factory fitted.

Dimensions Turntable

Width 448mm
Depth 365mm
Height 120mm (Dustcover closed)
Weight 5.2kg

Dimensions Neo PSU

Width 180mm
Depth 155m
Height 50mm
Weight 0.6Kg.

Ania moving coil cartridge
The newest member of the Rega MC cartridge range the Ania was inspired by the success of the Apheta 2 and Aphelion MC cartridges. Using the same exceptionally complex hand wound micro coil found in the rest of the range, the Ania is housed in a unique PPS highly rigid body, ensuring accurate construction and Rega’s three point fixing method ensuring optimum connection to the headshell and automatic setting for overhang. The new body is protected by a CAD designed, clear rigid cover to protect the internal fine wires, making handling whilst fitting, safe and risk free.The Ania features a super high-powered, neodymium magnet and a coil meticulously hand wound on to an iron cross. This miniature assembly allows us greater freedom to track the vinyl groove ensuring even more detail is extracted from the vinyl.

All of these features combine to deliver a balanced and dynamic performance that will engage you with your vinyl like never before.The Ania is the perfect partner for the Planar 3, Planar 6 or RP8 turntables. Factory fitted options for some models are available Please ask your retailer for details.

A unique design.

Rega’s Moving Coil cartridge design is unique in its approach to achieving an ultra-low mass generator which is undamped (no tie wire) using a unique rhomboid pivot for the cantilever powered by a purpose designed, exclusive to Rega, Neodymium magnet system. This type of design requires a zero-tolerance engineered cartridge body which is Rega’s area of expertise and with the Apheta 2 and Aphelion products these bodies are machined from one piece of the highest quality aluminium. This is a difficult and expensive process requiring all of Rega’s forty-four years of experience to achieve. In particular, the “zero” tolerancing of the body is required in the alignment and dimension of the pivot pad mounting hole and the magnet mechanism mounting hole relationship.

When we decided to produce a Moving Coil cartridge at half the cost of the Apheta 2, the special aluminium body could not be used, it was simply too expensive. The solution lay in an unusual polymer/glass combination called Polyphenylene Sulphide (PPS-Fortron). With 40% glass, this material could be moulded and would solve the cost problem. The special attributes of this material are its hardness and stability in shape and dimension post moulding, both critical for the performance of Ania. Now came the challenge. Rega designed and prototyped using SLA systems in just a few months, proving the validity of the design direction.

Now we had to design a production mould tool capable of extreme accuracy and long life. PPS is a difficult polymer to mould and requires special attention to how the mould tool operates. Couple this to an almost unmouldable complex shape of the Ania body and a very considerable challenge faced the Rega engineers and the toolmakers chosen. The toolmakers are of the highest technical skill level, using the most accurate Swiss EDM CNC machines, their regular customers being the military and medical industries, routinely working down to a micron (one thousandth of a millimetre).To achieve this intricate body shape required the most complex high pressure injection mould tool that Rega has ever designed. The tool has eight major parts, four of which must move in perfect synchronicity with each other to achieve each cartridge body. The design and manufacture of this “work of art” took an entire year to produce and was made exclusively by the most senior toolmaker requiring all his lifetime of artisanal experience.

Combine this special PPS body with its high specification stainless steel inserts, a unique rhomboid pivot system, a tried and tested high performance, diamond tipped elliptical stylus cantilever with low mass moving coil generator assembly and you have new market leading musicality, performance, speed, clarity, and detail as never before at this price.
Specifications:

Tracking Pressure 1.75 – 2.00g
Input load impedance 100 ohm
Output impedance 10 ohms
Nominal output voltage 350μV
Channel Balance : ≥ 20μV
Separation : ≥ -29dB

Mass 6g

Key Features:

Iron cross & micro coil assembly
One of the world’s smallest MC generators.
Cutting edge neodymium magnet.
Elliptical profile stylus
Constructed from high specification 0.018mm fine wire

Load settings for adjustable MC stages

Impedance -100ohm
Capacitance – 1000pF
Gain setting – High (‘On’ position for Rega phono stages)

Fono MC dip switch settings for all Rega MC models.

Exact.
Each one of our moving magnet cartridges are meticulously hand assembled to the highest standard by our highly trained technicians. The design and assembly procedure are focused on one simple goal, extracting as much music from your vinyl as possible.

Each one uses a pair of parallel wound coils which are then carefully assembled on custom jigs to create a working stereo generator. Each cartridge is then tested and checked over two days to ensure all of the strict parameters for each model are met before either packing or fitting to a Rega turntable.

The multi award winning, Rega moving magnet range offers unrivalled clarity, engaging stereo imaging and a natural dynamic performance, putting you in touch with your vinyl collection like never before.

Hand built moving magnet cartridge with three point mounting system and Vital profile diamond stylus with zero tolerance channel balance.

Output: 6.8 – 7.2mV
Stylus: Vital. Complex fine line micro-ground from a rectangular diamond billet.
Fixing: Rega three point fixing
Coils: High Spec parallel wound coils
Colour: Yellow
Tracking Pressure 1.75g.